AFM Safecoat WaterShield

Safecoat WaterShield Low-VOC Water Repellent Sealer
Safecoat WaterShield is a clear, versatile, controlled-penetration low-VOC water repelling sealer, which provides an invisible barrier against water and resists oils, grease and similar liquids. WaterShield is non-toxic, non-flammable, lead-free and formaldehyde-free, and does not contain surface contaminating silicones, making it a desirable coating for interior or exterior use. May be used on painted surfaces and may be painted over when dry. Dries clear and does not discolor. Contains 2g/l VOC content. Safecoat’s WaterShield has excellent adhesion and is easy to apply. In addition to sealing a providing a protective barrier against water migration, it helps to harden, dust-proof and control efflorescence in masonry surfaces.

Safecoat WaterShield Usage
Safecoat WaterShield can be used on porous, cementitious materials such as concrete, stucco, brick, block, terrazzo and unglazed tile. Can also be used to add water repellency to exterior vertical wood siding when applied over AFM Safecoat DuroStain.

Sizes
1 gallon & 5 gallon

Safecoat Low-VOC WaterShield Coverage
One gallon of Safecoat WaterShield covers approximately 250-300 square feet in one coat depending on method of application and surface porosity. Thinning: no reduction is required.

Safecoat Low-VOC WaterShield Surface Preparations
All surfaces must be clean, dry, free from dust, dirt, loose sand, mildew, efflorescence or any other foreign matter. The pH of the material to be sealed must be as close to neutral as possible, and definitely below 10. If the surface has been acid washed, for example to remove efflorescence, it must be thoroughly clean water rinsed and neutralized. Similarly, once mildew has been removed, for example by washing with chlorinated household bleach, the surface must be thoroughly rinsed with water and all bleach residue removed. Always use care with bleach and acid, and be sure to read and follow all warnings, label instructions and MSDS. Power wash, brush or scrape all surfaces and we sure to have a good, sound substrate before application of Safecoat WaterShield. Repair cracks, holes and repaint concrete block if necessary.

WARNING: Caution must be used when removing coating from existing surfaces. Surfaces should be checked for lead content. Sanding may create dust or dust particles that may contain lead, a hazardous substance. Avoid the creation and breathing of any dust particle. Always wear protective equipment. Breathing or eating lead containing dust or debris can cause health problems, especially in children or pregnant women.

Safecoat Low-VOC WaterShield Application
Always use adequate ventilation. Apply one coat with brush, roller, lambswool applicator or low pressure spray. When applying on vertical surface, start at the lower level and spray upwards. Flood until Safecoat WaterShield runs to assure complete saturation. On horizontal surfaces allow to sit for about ten minutes and remove any excess. Try to avoid puddling. Note: before using, check with water on test areas to be sure there is penetration. If there is none, do not use. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine which preparation and techniques are best suited to the specific surface.

Safecoat Low-VOC WaterShield Clean Up & Curing
Clean tools and equipment while still wet with a solution of SafeChoice Super Clean and warm water. Drying/Curing Time: Under normal conditions, Safecoat WaterShield dries within two hours and cures hard in 24 hours. Normal conditions include a clean, dry surface, access to fresh air flow, a dust free environment, moderate humidity and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat WaterShield to dry and cure more slowly.

Safecoat Low-VOC WaterShield Limitations
Unlike conventional sealers, Safecoat sealers are made without formaldehyde preservatives or toxic mildewicides or fungicides. Do not contaminate. Store in airtight containers. Do not use when indoor or surface temperature is below 55 degrees F. Do not apply where product will be immersed in water, such as fountains, pools or below ground area. Do not freeze.

Safecoat Low-VOC WaterShield Health Precautions
As with all coatings, keep container tightly closed and out of reach of children. Do not take internally. Always use adequate ventilation. Wear a mask when sanding and avoid breathing sanding dust. Avoid contact with skin and eyes and avoid breathing of spray vapors and spray mist. If you are chemically sensitive, always test for personal tolerance.

Safecoat Low-VOC WaterShield Limited Liability
Safecoat products are guaranteed not to be defective when properly applied. Liability express or implied is limited to replacement of product or refund of purchase price and does not include liability for labor costs or consequential damages. Variable factors out of manufacturer’s control, such as environmental conditions, application techniques, and surface conditions are critical to results obtained. Users are expected to exercise reasonable care to determine suitability of the product for each application. This limited warranty may not be modified or extended by manufacturer’s representatives, distributors, or dealers of AFM products. We strongly recommend that users always test in small inconspicuous areas before application to the entire surface.