AFM Safecoat DuroStain
Safecoat DuroStain Wood Stain
Safecoat DuroStain is a premium quality, fast-curing flat finish, semi-transparent stain. DuroStain is ideal for interior and exterior wood surfaces. It promotes penetration of porous surfaces and has high adhesion for superior protection as a decorative colorant. It has excellent pigmentation stability and is a durable stain. For use on all wood surfaces. DuroStain contains no aniline dyestuffs, no gilsonite or asphalt, no aromatic solvents and no formaldehyde. Contains 56g/l VOCs.
Safecoat DuroStain Usage
Safecoat DuroStain is recommended for unsealed wooden surfaces. Note: staining large surfaces such as floors with a water-based stain requires significant expertise and is not recommended for the average user.
Safecoat DuroStain Benefits
- Excellent, light fast pigmentation stability
- Superior, durable stain
- Safely used by and for the chemically sensitive
- Low odor, non-offensive to installer and occupant
- Very low VOC content (56g/l)
- Meets or exceeds all Federal and State air quality regulations, including California
Safecoat DuroStain Coverage
One gallon of Safecoat DuroStain covers approximately 300 square feet in one coat depending on surface porosity and the intensity of the stain color desired.
Safecoat DuroStain Colors
Durostain is available in Clear, Cedar, Mahogany, Redwood, Walnut, Oak, Birch and Maple. Stains may be mixed together to modify color. NOTE: Safecoat Durostain uses natural mineral pigments and slight variation in color may accordingly occur between batches. Always use material from the same batch for a specific job.
Safecoat DuroStain Usage Surface Preparation
Because of wide variations in the way different woods accept stain, we particularly recommend that users always test in small, inconspicuous areas for appearance and compatibility before application to the entire surface. Surfaces to be stained with Safecoat DuroStain should be sound and cleaned or dirt, dust, grease, wax, silicone, soap and oil, and must be completely free of mold, mildew or fungus contamination. Cleaning with an odorless, dye-free, all-purpose cleaner like SafeChoice Super Clean is recommended. Previously painted or sealed surfaces will not accept stain readily. Consequently, stripping of old paint or sealer followed by rinsing and sanding will be required before application of Safecoat DuroStain to achieve maximum penetration from this product. Surface can be dampened with water to assist user in getting an even application. Porous woods with strong grain pattern can be tamed by using thinned (50% with water) application of Safecoat DuroStain Clear. Safecoat DuroStain can be used as a glaze over painted and sealed surfaces.
Safecoat DuroStain Application
Always have adequate ventilation. Intermix (boxing) all containers of the same color to ensure uniformity before applying. Before using, stir Safecoat DuroStain well, then apply it evenly without reduction using a high quality nylon or synthetic bristle brush. To adjust intensity of color, best results will be obtained by staining six foot sections (2′ x 3′) of the surface and wiping off excess stain while it is still wet to achieve the desired intensity of color. Always keep a wet edge. Darkness of stain may be increased by high surface porosity, wiping off less stain, or letting the stain dry longer before wiping. A squeegee applicator can be beneficial when coating large flat surfaces like doors. The shade of the stained surface will be affected by the color and type of wood. Reduce if desired for spraying with up to 1/2 pint of water per gallon. Always use a painter’s mask when spraying. Do not apply in direct sunlight. Make sure to wipe off any excess stain which does not penetrate into the wood. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine what preparation and techniques are best suited to the specific surface.
Safecoat DuroStain Clean Up
Under normal conditions, Safecoat DuroStain dries to touch in one hour and is re-coatable after two hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat to dry and cure more slowly. Clean tools and equipment while they are still wet with a solution of SafeChoise Super Clean or SafeChoice Safety Clean and warm water. To recycle or properly dispose of paint in your community call 1-800-CLEANUP (USA only) or visit www.Earth911.org.
Safecoat Durostain Limitations
Unlike conventional stains, Safecoat DuroStain is made without formaldehyde preservatives or toxic mildewcides or fungicides. Do not contaminate. Store in airtight containers. Do not use when indoor or surface temperature is below 55 degrees F. Do not freeze. Use of Safecoat DuroStain outdoors may require the addition of a mildewcides or fungicide to prevent attack by spores before the stain cures.
Safecoat DuroStain Health Precautions
As with all coatings, keep container tightly closed and out of the reach of children. Do not take internally. Always use adequate ventilation. Wear a mask when sanding and avoid breathing sanding dust. Avoid contact with skin and eyes and avoid breathing spray vapors and spray mist. If you are chemically sensitive, always test for personal tolerance.
Safecoat DuroStain Limited Liability
Safecoat products are guaranteed not to be defective when properly applied. Liability express or implied is limited to replacement of product or refund of purchase price and does not include liability for labor costs or consequential damages. Variable factors out of manufacturer’s control, such as environmental conditions, application techniques and surface conditions are critical to results obtained. Users are expected to exercise reasonable care to determine suitability of the product for each application. This limited warranty may not be modified or extended by manufacturer’s representatives, distributors or dealers of AFM products. We strongly recommend that users always test in small inconspicuous areas before application to the entire surface.
